The Near and Far Future for Orbotech and Inspection

Reading time ( words)

Orbotech’s PCB Division President Arik Gordon and I spoke in detail about the company’s newest developments in automated optical shaping (AOS), Orbotech’s unique culture and commitment to R&D, and what he expects to see in the near future for the inspection industy.

Barry Matties: Arik, for those few who may not know, please tell us a little bit about what Orbotech does.

Arik Gordon: Orbotech is a global player in the production of electronic components, enabling their manufacture. We have three business divisions: FPD or flat panel display division which plays a major role in the production cycles of flat panels made for TVs, smartphones or any advanced electronic device with a screen including watches, cars and much more; SPTS, which we acquired in 2014 and is our semiconductor devices division or SDD and offers process equipment for the backend of the semiconductor manufacturing process, for example advanced packaging as well as MEMS, power devices and much more; and the PCB division that I head up, which focuses on developing advanced manufacturing solutions for the production of printed and flex circuit boards.

The three divisions are more or less the same size, each contributing between 25–35% of Orbotech's revenue, and today it's extremely hard to find an advanced electronic device that was not manufactured using Orbotech’s systems at one or more stages of production.

Matties: Orbotech is the giant in the industry for the inspection arena, but you have a lot of other technology. Let's focus on the PCB side. You have your automated optical repair or AOR, but you have also been describing a new process that does 3D modeling. Tell us a little bit about that process and the new solution.

Gordon: It is true that we started in inspection and yield enhancement. However, for more than 10 years now the main focus of our business has been production solutions such as direct imaging, which is our largest product and is clearly a production system, or what you referred to as AOR, which we have evolved into AOS or automated optical shaping.

Matties: Shaping—that's the word I was looking for. What is shaping and what’s the difference between shaping and repair?

Gordon: Shaping and repair are not the same thing. Not even close. The distinction between these two concepts is extremely important since shaping will play a key role in the future of electronics as technologies advance, functionality increases and devices become even smaller and lighter.  The key distinction between repair and shaping is that repair is performed manually and is not suitable for the fine lines and high resolutions that we are seeing more and more these days, especially with advanced HDI and mSAP. With shaping we actually analyze the circuit using AOI technologies and make sure that the original CAM design is accurately produced. Where necessary, when there are shorts or opens of any type, we 3D shape or 2D shape the design, ensuring that the original CAM design is re-created.

Matties: Is shaping a new addition to the industry lexicon that you're trying to introduce?

Gordon: Yes, definitely.

Matties: Because you don't want to call it ‘repair’ due to connotations of poor quality, or some other issues that an OEM might reject the boards for?

Gordon: The repair process in the PCB industry is not a clean process that is well-controlled.  What we do with shaping and the Precise™ 800 is well beyond it.  It's more like plastic surgery. We work according  to the CAM design, and there are multiple checks to ensure that the original design is properly produced.

The process starts by removing  excess copper with a laser—an extremely complex and delicate process as the copper is on top of a laminate. You need a high powered laser to melt the copper, but you need to do it without damaging the substrate. With our 3D shaping, we actually add copper to the circuit and 3D shape opens. The amount of PCBs that this groundbreaking technology can save from the scrap heap is huge.

Matties: How many of these units have you placed now into the market?

Gordon: We launched the PerFix which removes excess copper a few years ago, and there are about 300 systems in the market so far.

Matties: And how many of your new shaping solution, the Precise 800?

Gordon: The Precise was launched at CTEX 2016 in May. I think it's fair to say that we have received tens of orders for this solution so far.

Matties: Nice, so it's well accepted.

Gordon: It's well accepted, yes.

Matties: Why do you think it’s been so well accepted so quickly?

Gordon: I think what is happening is that the complexity of the PCBs, especially in HDI, is getting to a level where the old style of repair is simply not possible—the lines are too thin, the laminate is too thin, and the only way to increase the yield is to use this new type of system.

Matties: Let’s talk about DI for a minute. There's a lot of new competition in the DI space.

Gordon: Yes.

Matties: How is that impacting what you do, or does it?

Gordon: Competition always impacts the business, and so I’ll divide my answer in two. Direct imaging is typically used in the advanced circuit board HDI and up. We have a unique technology called LSO or large scan optics, where we have typically one large lens or optical element as opposed to most of the competition which uses an area with many smaller lenses or optical elements. The main advantage of our technology is depth of focus, which is critical for production in terms of robustness.  Both systems will perform well during a demonstration, however, in real-life scenarios when the panels are a little warped and you need day-in, day-out production, large scan optics is a core element and has a significant advantage.

And of course, the system is very fast. With real-time scaling and many other benefits, it has an edge over the competition. In the high-density boards, we estimate the market to be about 50% for many years now, thanks to the robustness and capabilities of the system. 

Matties: You also have the ability of bundling because with your portfolio customers can come in and buy a universal package, which certainly gives you an advantage in the negotiating room.

Gordon: Definitely. If you look at the PCB production process in the context of Industry 4.0, you can see how many steps are covered by Orbotech equipment. We are also a major shareholder of Frontline which offers CAM solutions to most of the industries from CAM to inspection to direct imaging, inkjet, laser drilling and shaping. We have other offerings as well which support the direct imaging business.

Matties: What about solder mask? Is this also a big area now?

Gordon: Yes, there is a high demand for direct imaging of solder mask. The requirements are somewhat different than patterning. The most obvious is that we require very high energy to expose the solder mask material. For that, we launched a system called Diamond. To the best of our knowledge, it's the fastest system in the market. It's in penetration mode at the moment, and we believe that it will play a significant role in our business.

Matties: Is this solution capable of high-volume production? I know there are others out there that aren't quite so high volume.

Gordon: Our equipment is always designed for high-volume production.

Matties: So what hurdles did you have to overcome to gain speed?  It's all about speed, right?

Gordon: Speed and power. Typical dry film resist in HDI and patterning can need 20 to 30 millijoule per cm2 of energy to expose it, and solder mask requires hundreds, if not sometimes thousands, of millijoules per cm2 to expose it. We had to come up with a system that has high power. Also, the solder mask is more sensitive to the spectrum of the light. The laser is typically a single wavelength but here we had to come up with a system that has multiple wavelengths, and that was a technological challenge, so it took us years to develop.

Matties: How has the market reacted to this product line?

Gordon: That product was also launched in 2016 and the business is growing. At the same time, we are continuing to address the key challenges, including the hundreds or even thousands of types of different solder mask materials out there which all interact differently with different sources of energy. We have to adapt the system to the needs of different solder mask materials. Of course it takes time, but it's gaining momentum and next year we hope to sell tens of systems.

Matties: You have solutions or products for just about every fabricator in the world really. There's not a fabricator that couldn't benefit by using one of your products, if not multiple.

Gordon: Yes. If you look at the top 50 PCB makers, the vast majority would already have a significant amount of Orbotech equipment and I think we are a major partner to our customers.

Matties: What impressed me is the amount of R&D and the commitment to R&D that Orbotech has. Can you talk about that? It's quite impressive.

Gordon: That’s very true and is one of our key differentiators. Orbotech is a highly technology-oriented company. It was founded that way and over the years, we’ve managed to keep our culture and spirit, but it also comes down to our investment in R&D. We keep the company R&D at quite a high level. In good years, it's between 12 and 14%, but the industry is cyclical and some years it rises much higher because we try to keep the investment in R&D level, even in a downturn. In general, that’s our culture: we're a long-term player and we are committed to investing in the future.

Matties: Now, I’m sure you've heard this, for some there's a love-hate relationship with Orbotech, and some people complain about the service fees, for instance. How do you deal with that? The second part to that question is, I think a lot of your competitors use that against you in many ways too. How do you deal with that? Are you familiar with those statements?

Gordon: I’m familiar with those statements, and I think it used to be true many years back. There are cases here and there where this is still the customer’s perception, but it’s the exception and not the rule. We are in a unique situation. We are a very significant player in the industry and there’s a very delicate balance involved in using that significance in a way that is perceived as partnership and not an organization that causes or forces others to buy equipment. Today, there is competition in each and every product line that we have, which in a way also helps to keep us humble. But also the culture and approach that we have been taking in recent years has definitely tackled that point. Today, I don’t believe that you will find many customers that still hold that view.

Matties: I think you're right that the volume has diminished, the decibels are lower, but we still do hear that, particularly when times are tough. Because they have to put out cash and their revenue is maybe not so good.

Gordon: One more point to mention in that context is most of the employees in the PCB division, which is about 750 employees overall, are customer support engineers. We continue to maintain systems that were launched 20 years ago and that operation includes powerful legacy systems as well as new systems. We sell to customers in Europe, U.S., England, China including Taiwan, Korea, Japan and many areas in Southeast Asia, both in centrally located and remote areas. To maintain a customer support organization that services all these types of equipment is a costly operation. We do charge our customers and in return, we try to deliver consistently high value.

We provide our customers with a complete safety net and a low level of risk. Yes, they have to pay for the service, but they also know that it's there. It may take one day more, one day less, but we are there for them and we are always working on improving that.


Suggested Items

Korf and Strubbe: Material Witnesses

10/03/2022 | I-Connect007 Editorial Team
Recently, columnist Dana Korf has been working with Taiwan Union Technology Corporation (TUC), one of the largest providers of copper-clad laminate and mass lamination services in the world. We spoke with Dana about the trends he sees in materials at TUC and around the globe, why copper is still king, as well as some potential non-traditional materials that may see growth soon. Dana invited John Strubbe, TUC VP of technology, to join in the conversation.

Michael Carano: A Focus on Process Control, Part 2

09/28/2022 | I-Connect007 Editorial Team
In this second half of our conversation, Michael Carano discusses some of the metrics that fabricators need to consider before investing in new processes, especially process control technologies, and some of the challenges board shops face updating brownfield sites.

Catching Up With John Johnson, New Director of Business Development at ASC

09/28/2022 | Dan Beaulieu, D.B. Management Group
It’s always good to catch up with old friends, especially when you can start working together. I recently spoke with my friend John Johnson, who has joined American Standard Circuits as the director of business development. At ASC, John will be using the Averatek A-SAP process that he was previously involved with. He shares some of his background and provides insight on the best ways to use this semi-additive PCB fabrication process that opens the capability window for forming trace and space.

Copyright © 2022 I-Connect007. All rights reserved.