Atotech Launches New Horizontal Bonding Enhancement Solution for HF Applications


Reading time ( words)

BondFilm HF is Atotech’s new process for the treatment of inner layer cores. It leads to highest bonding performance in the manufacture of multilayer & HDI printed circuit boards. This innovative new process maintains the excellent performance first developed in the BondFilm product range whilst offering the lowest possible signal loss as required in high frequency applications. 

Circuit design is already planning towards the low signal loss requirements of the next generation of network technology, the so called 5G. To meet these signal integrity demands the ideal would be to use a non-etching adhesion promotor system. However, whilst such systems are available in the market, they are not yet widely established. BondFilm HF bridges the gap with significantly reduced surface roughening which helps meet the signal integrity requirements whilst maintaining excellent bond strength and functional performance. 

BondFilm HF

The latest development in Atotech’s BondFilm product range is BondFilm HF. Copper panels treated with BondFilm HF have the typical uniform, brown organo-metallic coating long associated with the BondFilm® process. This coating retains the excellent enhanced bonding between the inner layer and prepregs used in multilayer manufacture but with one significant difference: only minimal roughening is needed.  

In previous versions of the BondFilm process development targets have been to maximize the surface roughening to give the best possible multilayer bond strength; here, the target was to provide this functional performance without compromise but with a minimal roughening of the copper traces. By producing this low roughening of the copper surface a significant reduction in signal loss in the „skin“ of the copper traces is achieved. This makes BondFilm HF more suited to high frequency applications where signal integrity is paramount. 

Production trials using BondFilm HF focused on the functional properties of the multilayer boards together with electrical signal loss measurements. Data shows that panels manufactured with BondFilm HF fulfill all reliability tests considered, such as thermal stress tests and performance multiple iR reflow cycles. At the same time they significantly outperform panels made with conventional treatment processes in terms of reduced signal loss. 

BondFilm HF is a simple drop in replacement for existing BondFilm process users. Its short process sequence is also compatible with most existing oxide alternative lines.  

The process is already installed in a leading Chinese manufacturer and shows excellent results with first customer evaluations. Its key benefits in terms of significantly reduced signal loss gives this new process a considerable advantage for all high frequency applications. 

About Atotech

Atotech is one of the world’s leading manufacturers of specialty chemicals and equipment for the printed circuit board, IC-substrate and semiconductor industries, as well as for the decorative and functional surface finishing industries. Atotech has annual sales of USD1.2 billion (2017). The company is fully committed to sustainability – we develop technologies to minimize waste and to reduce environmental impact. Atotech has its headquarters in Berlin, Germany, and employs about 4,000 people in over 40 countries. About a quarter of all staff works in one of the four locations in Germany: Berlin, Feucht, Neuruppin, and Trebur. For more information, click here.

Share

Print


Suggested Items

Laser Focus on Flex and Rigid-flex

01/28/2019 | Barry Matties, I-Connect007
ESI’s Chris Ryder, director of Product Management, and Shane Noel, Flex Systems product manager, discuss laser vias for flex users and the increasing necessity for companies to collaborate early on and become more and more involved, whether that be in the product design, or with the process or base material manufacturers.

Atotech at HKPCA on Announcements and Advancements

01/21/2019 | Edy Yu, I-Connect007
Edy Yu, managing editor for PCB007 China, caught up with Daniel Schmidt, Atotech’s director of global marketing, during the 2018 HKPCA and IPC Show in December. Edy and Daniel discussed Atotech’s new announcements at the show including their new solutions for 5G, high-speed, and high-frequency applications, and more.

ESI’s Chris Ryder: There’s More to Choosing a Laser Than You Think

01/16/2019 | Barry Matties, I-Connect007
At the recent HKPCA show, I sat down with ESI’s Chris Ryder, director of product management—HDI—to discuss considerations for choosing a new laser system, and how ESI uses its decades of flex and rigid-flex drilling experience to help guide customers in their decision-making process.



Copyright © 2019 I-Connect007. All rights reserved.