Flex on the Brain: The Future of Neural Interfaces


Reading time ( words)

The SMTA Additive Electronics TechXchange took place virtually on October 14, with presentations from a wide variety of technologists involved in additive processes. Organizers Tara Dunn of Omni PCB and Lenora Clark of ESI Automotive did a great job putting together this event.

Duke1.jpg

One of the highlights was a presentation titled “Flexible Electronics for Neural Interfaces” by Dr. Jonathan Viventi, assistant professor of biomedical engineering at Duke University. His research with flexible electronics has helped create new types of technology for interfacing directly with the human brain, allowing high-resolution scans over wide areas. This technology can diagnose and treat all kinds of neurological disorders, including epilepsy.

Duke3.jpg

In a fascinating presentation, Viventi explained that earlier brain sensors were impractical, often using thousands of electrodes, and they offered only two options: a high-resolution scan of a small part of the brain or a low-resolution shot of a broad area.

Duke2.jpg

Now, Viventi’s new flexible silicon interface fits directly onto the brain and can provide a high-res look at a wide area. He noted that silicon could behave just like a flexible circuit if you make it thin enough. In his research at Duke, Viventi has investigated the use of LCP and polyimide, both of which use additive processes, and they’re fairly inexpensive as well.

Duke5.jpg

His interface has been tested and found to be safe on rats and monkeys. Now, humans having brain surgery can volunteer to have one placed on their brain and removed when surgery is completed. Viventi explained that placing the flexible silicon on the brain isn’t too dangerous.

Duke7.jpg

“The brain is actually pretty tough,” Viventi said. Doctors induce a seizure with drugs, and they’re able to detect waves propagating through the brain that they were missing before. Previous tools just didn’t have high enough resolution.

Interestingly, the human subject stays awake during the brain scan. Viventi said the doctors ask patients to answer questions during the procedure. I don’t know if I’d like that part, but I see the point. Viventi said plans are underway to scale up to commercial CMOS silicon; each of these interfaces would replace 65,000 electrodes.

Duke6.jpg

LCP interfaces are especially robust, with accelerated aging showed that they would last more than five years at 37°C, and they offer great biocompatibility. Viventi’s research is a great reminder of how technology is being used to save lives and treat neurological disorders every day.

Duke4.jpg

Share




Suggested Items

Part 2: The Printed Electronics Roundtable

09/22/2022 | Andy Shaughnessy, Design007 Magazine
We recently held a roundtable with a team of printed electronic circuit experts from companies that run the gamut: John Lee and Kevin Miller of Insulectro, Mike Wagner of Butler Technologies, Tom Bianchi of Eastprint, and John Voultos of Sheldahl Flexible Technologies. In the first part of this roundtable, the team dispelled a variety of myths surrounding PEC. In this second part of the roundtable, the participants discuss what designers and fabricators need to know to jump into printed electronics, and some of the drivers behind this growing technology.

Just Ask Tara Dunn: Will IC Substrates Be Produced in Volume in the U.S.?

12/01/2020 | I-Connect007 Editorial Team
First, we asked you to send in your questions for Happy Holden, Joe Fjelstad, John Mitchell, and others in our “Just Ask” series. Now, it’s Tara Dunn’s turn! Tara is the vice president of marketing and business development for Averatek. Today's question: Do you think IC substrates (BGA, CSP, flip chip, etc.) will ever be produced in high volumes in the U.S.?

Just Ask Tara Dunn: DFM for Flex and Rigid-Flex

11/06/2020 | I-Connect007 Editorial Team
First, we asked you to send in your questions for Happy Holden, Joe Fjelstad, John Mitchell, and others in our “Just Ask” series. Now, it’s Omni PCB President Tara Dunn’s turn! A regular Flex007 columnist, Tara discusses flexible circuits, rigid-flex, and rigid PCBs, as well as RF/microwave technology, microelectronics, and additive processes. Tara is the co-founder of Geek-a-Palooza and a show manager for the SMTA Additive Electronics TechXchange event. She has over 20 years of experience in the PCB industry. We hope you enjoy “Just Ask Tara.”



Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.