All About Flex: Soldering Flexible Circuits


Reading time ( words)

The most common methods for component attachment on flexible circuits and rigid printed circuit boards involve soldering. The basic principles for soldering are the same for both flex and hard board, but soldering components to flexible circuits involves certain specific considerations vs. our rigid cousins. The nuances are related to material handling and flexibility; reflowed solder is not flexible and can fracture under the various stresses a circuit may experience. Flexible circuits are also more likely to absorb water as polyimide is hydroscopic. With this condition, pre-baking the circuitry prior to soldering at 105°C for 30–60 minutes is recommended to ensure delamination will not occur from thermal shock. This is especially true in high humidity conditions. In addition, adhesive systems use different formulations on flexible circuits vs. hardboards and this sometimes creates hand soldering challenges. As a result, design layout and manufacturing techniques for flex circuit soldering need to be slightly different vs. rigid PCBs.

Design/Layout Considerations

Bending, twisting and flexing can put a great deal of mechanical stress on the trace and solder in areas near bend or transition points. Additionally, the adhesive system that bonds copper to the dielectric substrate (often acrylic or a modified epoxy) has been formulated to provide different properties vs. the epoxy adhesive system used for the vast majority of rigid printed circuit boards. The epoxy adhesive for a rigid PCB is cast onto reinforcement strands of a glass fiber carrier. Curing the epoxy with the glass creates a rigid substrate. But in order for a flexible circuit to flex, the adhesive system needs to allow movement. So the adhesive system for a flexible circuit is “softer” and less cohesive than the adhesive system for a PCB. When exposed to the high temperatures of the soldering iron, the adhesive system may soften a bit. In order to compensate for this, many design guides recommend a design feature known as “anchor spurs” or tie downs as shown in Figure 1.

Fig1.jpg 

Fig2.jpgSolder joints should not be subjected to the stress of bending. It is a good idea to make sure that flex points are far enough away from the solder pad to prevent stress. Figure 2 shows the issue with a plated via, but the same issue applies to a solder filet. The bend radius guideline using 10X the material thickness is a safe rule for repeated flexing. Flexible circuits are often folded onto themselves in one time bend applications.

Fig3.jpgSince a flexible circuit can easily conform to surface irregularities, it is important to consider if the solder joint will match up with potential stress points. One example is shown it Figure 3. The end of the stiffener creates a stress point directly under the solder joint. This situation should be avoided.

Soldering Techniques

Even with the design optimized for solder joints, the soldering methods for flexible circuits may need to differ from a rigid printed circuit board. In hand soldering, operators must use a bit more care when soldering to flex than when soldering to a rigid PCB. In either case, only a minimal amount of solder iron pressure is needed to form a good solder joint. There is less latitude for excess solder tip pressure with flexible circuits as pressure can cause the pad to slide or move when the heat temporarily softens the adhesive. Excess temperature or dwell can also cause the copper pad to delaminate from the film coverlay and/or substrate. Adhesiveless laminates have become much more popular during the past 10 years and are more robust when exposed to soldering temperatures.

SMT assembly is a little different with flex. Rigid printed circuit boards can be easily held and shuttled since they are mechanically robust enough to be lifted by the edges and placed onto a conveyor. Flexible circuits are flimsy and often require fixturing or modifications to be compatible with the SMT handling system to shuttle the flexible panel through the solder dispense, SMT placements and reflow ovens.

Wave soldering flex will usually require special fixturing. Normally the flexible panel is positioned on top of a rigid surface, “solder side” down, where there are openings milled out to expose the areas to be soldered.

In both the cases of SMT soldering and wave soldering, there are usually several duplicate fixtures needed to assure equipment productivity as fixtures are not available for reuse until circuits go through the entire process. Fixturing and tooling used for SMT assembly and wave soldering are quoted as part of the total tooling package. The fixturing can vary significantly in complexity and cost depending on the circuitry configuration, component types, tolerances and locations.

Dave Becker is the V.P. of sales and marketing at All Flex Flexible Circuits and Heaters.  To contact Becker, or read past columns, click here.

 

Share




Suggested Items

EIPC Technical Snapshot: Supporting Autonomous Driving

05/12/2022 | Pete Starkey, I-Connect007
EIPC’s 17th Technical Snapshot webinar on May 4 focused on developments in automotive electronics, particularly on advances in the technologies required to support the evolution of autonomous driving. The team brought together two expert speakers to present their detailed views on topics encompassed within “CASE,” the acronym that appears to be taking over the automotive industry.

I-Connect007 Editor’s Choice: Five Must-Reads for the Week

05/06/2022 | Andy Shaughnessy, I-Connect007
This week, we have some M&A news from Summit Interconnect, and a variety of columns. Chris Bonsell discusses the lack of preventive maintenance planning in PCB manufacturing, and Kelly Dack lays out some solder mask guidelines for PCB designers. Duane Benson helps make sense of the quoting process in a time of 50-week lead times, and Dan Beaulieu has a great review of a book about how shareholder policies have caused many of the problems we see in corporations today.

Institute of Circuit Technology: A Novel Approach to Recycling PCBs

03/10/2022 | Pete Starkey, I-Connect007
A two-year project funded by an Innovate UK SMART Grant aims to reduce the impact of e-waste using naturally derived, biodegradable and nontoxic products. Those attending the webinar for the Institute of Circuit Technology’s annual meeting on March 2 learned more about the project, as well as statutory paperwork obligations of the UK REACH regulations. Following the formal business, ICT Chair Emma Hudson introduced and moderated this technical webinar.



Copyright © 2022 I-Connect007. All rights reserved.