-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Book Excerpt: The Printed Circuit Designer’s Guide to... Thermal Management with Insulated Metal Substrates, Vol. 2, Chapter 3
March 1, 2024 | I-Connect007 Editorial TeamEstimated reading time: 1 minute
Chapter 3: Thermal Resistance/Impedance and Measurement
Note that several measurement methods are in common use and typically produce different results. Obviously, this can cause confusion. The Rth value of a thermal resistance, or its thermal conductivity, is meaningless if the test method is not specified.
Following is a brief review of the different measurement methods:
ASTM E1461
The image on the left in Figure 3.1 shows the experimental setup and measurement principle for the test method ASTM E1461 (Standard Test Method for Thermal Diffusivity by the Flash Method). This is a contactless test method for high-temperature testing using a laser. One surface of the test sample is irradiated with a flash of the laser and the thermal transfer to the other side is measured using an infrared detector.
A test sample measured according to ASTM E1461 was shown to have thermal conductivity of 3.3 W/mK.
ISO 22007-2
The center diagram in Figure 3.1 describes the test setup and measurement principle for testing according to the ISO 22007-2 transient plane heat source (hot disc) method. This method allows fast testing and high accuracy, eliminating opportunities for measurement failures and yielding a value without transfer losses. The test sample needs to be at least 3 mm thick.
Using this setup to test the same sample as in the previous ASTM E1461 test showed the thermal conductivity to be 5 W/mK.
ASTM D5470
The diagram on the right in Figure 3.1 describes the test method ASTM D5470. A heat flow is set up through the sample, establishing a temperature gradient that is measured in the steady state. The thermal conductivity/resistance of the sample is then calculated using a method described in the standard.
Suggested Items
Real Time with… IPC APEX EXPO 2024: Software Solutions for Circuit Board Challenges
05/03/2024 | Real Time with...IPC APEX EXPONolan Johnson speaks with Will Webb from Aster Technologies about their software solutions for design teams, manufacturing, test engineers, and process engineers. Aster's software addresses the increasing complexities of circuit boards and the need for alternative testing methods.
Manta Ray UUV Prototype Completes In-Water Testing
05/02/2024 | DARPAThe Manta Ray prototype uncrewed underwater vehicle (UUV) built by performer Northrop Grumman completed full-scale, in-water testing off the coast of Southern California in February and March 2024.
Real Time with… IPC APEX EXPO 2024: Exploring Electronic Card Testing and AI Integration with SPEA
05/02/2024 | Real Time with...IPC APEX EXPOLuca Fanelli, president of SPEA, and vice president Andrea Furnari discuss the company and its business units. The challenges in testing electronic cards and SPEA's solutions are discussed, and its focus on the US market is emphasized. The use of AI in testing, particularly in optical inspection and test program execution, is also examined.
Boeing T-7A Red Hawk Triples Progress
05/01/2024 | BoeingThe Boeing T-7A Red Hawk achieved three recent milestones, propelling the advanced pilot trainer for the U.S. Air Force forward.
Keysight Secures New Test Case Validations for Narrowband Non-Terrestrial Networks Standard
04/30/2024 | Keysight TechnologiesKeysight Technologies, Inc. has validated new conformance test cases for 3rd Generation Partnership Project (3GPP) Release 17 (Rel-17) standards for non-terrestrial networks (NTN) using narrowband internet of things (NB-IoT) technology.