Atotech to Present New Flex, Flex-Rigid Products at C’Tex 2018


Reading time ( words)

Atotech will showcase its latest production solutions for advanced HDI, flex, and flex-rigid PCBs in hall C1, booth AN6 at the C’Tex 2018 show. The trade show will be held in the Suzhou International Expo Center from May 16-18. Next to its product promotion at its trade show booth, the company takes part in the New Product Introduction sessions with the introduction of its new InPro THF chemistry.

On Thursday, May 17, from 2:00 to 2:40 pm, Mustafa Oezkoek, Global Product Manager for Panel and Pattern Plating at Atotech Deutschland GmbH, will present InPro THF for advanced HDI (mSAP). InPro THF provides reliable BMV filling performance at high current densities up to 3 A/dm² especially for mSAP applications in mass production. The process meets the technological and yield requirements for next generation HDI and packaging and provides pattern plating with excellent pattern distribution. It may also be used for TH filling and reduces the number of processing steps needed, thereby leading to improved reliability, productivity, and reduced costs. The three additive component system further provides excellent stability without the formation of harmful breakdown products. 

InPro THF: Current density: 3.0  A/dm², dimple < 3μm

Additional product highlights at Atotech’s booth will be Cupracid Flex / InPro Flex, an economic conformal plating solution for standard flex and rigid-flex applications, and Stanna-COF, an immersion tin for chip on film technology.

Cupracid Flex / InPro Flex

Cupracid Flex and InPro Flex are specifically designed for standard conformal flex applications. The Cupracid Flex process is for use in vertical systems with soluble anodes whereas InPro Flex can be used in systems with insoluble anodes. Even at higher current density, pattern uniformity and line shape are very good. Both processes consist of a simple two additive system and provide excellent throwing power at high current densities without any corner flattening.

Stanna-COF

Stanna-COF is the latest extension to Atotech’s already well versed immersion tin family. The application enables Chip On Film (COF) technology. With Stanna-COF, the chips are bonded straight onto the tracks necessitating a smooth and even finish. The process assures improved yields and functionality and allows for high volume reel to reel production. Stanna-COF has the potential to enhance fine line capability and provides a protective and functional final finish as demanded by this technology.

For further information on these new products, visitors to the show are invited to join Atotech’s New Product Introduction presentation or pass by the Atotech booth in hall C1 number AN6 during the C’Tex show from May 16 to 18. Local and international product specialists will be on site to discuss any question or inquiry.

About Atotech

Atotech is one of the world’s leading manufacturers of specialty chemicals and equipment for the printed circuit board, IC substrate and semiconductor industries, as well as for the decorative and functional surface finishing industries. Atotech has annual sales of USD1.2 billion (2017). The company is fully committed to sustainability – we develop technologies to minimize waste and to reduce environmental impact. Atotech has its headquarters in Berlin, Germany, and employs about 4,000 people in over 40 countries. About a quarter of all staff works in one of the four locations in Germany: Berlin, Feucht, Neuruppin, and Trebur. For more information, click here.

Share




Suggested Items

Plating on Silver: What’s Old is New Again

07/07/2022 | Denis Jacques, Technic Inc.
About three decades ago, immersion silver, a nitrate-based process, gained a lot of market share in the world of PCB final finishes. More economical than ENIG, flat, solderable, and conductive, it had everything going for it—everything but corrosion resistance in a harsh environment, that is. Champagne voids were also an issue, along with line reduction. But the worst drawback, the characteristic that made the part short over time, was creep corrosion. A build-up of copper sulfide salt that grows in contact with a sulfur-rich environment, heat, and moisture resulted in failures in the field. This was enough to scar the process for good.

EIPC Summer Conference 2022: Day 2 Review

06/29/2022 | Pete Starkey, I-Connect007
Örebro, Sweden on June 15 brought a bright and early start to Day 2 of the EIPC Summer Conference for those who had enjoyed the previous evening’s networking dinner, but had resisted the temptation to over-indulge or to carry on their long-awaited catch-up conversations with old friends into the small hours. All but a few were in their seats for 9 a.m., awake and attentive for Session 4 of the conference, on the theme of new process technologies, moderated by Martyn Gaudion, CEO of Polar Instruments.

Technica Heats Up ROI Discussion

05/17/2022 | I-Connect007 Editorial Team
The I-Connect007 Editorial Team speaks with Technica’s Frank Medina, Ed Carrigan, and Jason Perry about trending hotspots that provide the PCB fabricator a high return on investment (ROI). A theme that carries throughout the conversation is that traditional methods for calculating ROI are being replaced by models that include more qualitative factors.



Copyright © 2022 I-Connect007. All rights reserved.